Manual Pages  — SCTP_SENDMSG

The address of the target is given by to with tolen specifying its size. The length of the message msg is given by len. If the message is too long to pass atomically through the underlying protocol, errno is set to EMSGSIZE, -1 is returned, and the message is not transmitted.

No indication of failure to deliver is implicit in a sctp_sendmsg(3) call. Locally detected errors are indicated by a return value of -1.

If no space is available at the socket to hold the message to be transmitted, then sctp_sendmsg(3) normally blocks, unless the socket has been placed in non-blocking I/O mode. The select(2) system call may be used to determine when it is possible to send more data on one-to-one type (SOCK_STREAM) sockets.

The ppid argument is an opaque 32 bit value that is passed transparently through the stack to the peer endpoint. It will be available on reception of a message (see sctp_recvmsg(3)). Note that the stack passes this value without regard to byte order.

The flags argument may include one or more of the following:

#define SCTP_EOF          0x0100        /* Start a shutdown procedures */
#define SCTP_ABORT        0x0200        /* Send an ABORT to peer */
#define SCTP_UNORDERED    0x0400        /* Message is un-ordered */
#define SCTP_ADDR_OVER    0x0800        /* Override the primary-address */
#define SCTP_SENDALL      0x1000        /* Send this on all associations */
                                        /* for the endpoint */
/* The lower byte is an enumeration of PR-SCTP policies */
#define SCTP_PR_SCTP_TTL  0x0001        /* Time based PR-SCTP */
#define SCTP_PR_SCTP_BUF  0x0002        /* Buffer based PR-SCTP */
#define SCTP_PR_SCTP_RTX  0x0003        /* Number of retransmissions based PR-SCTP */

The flag SCTP_EOF is used to instruct the SCTP stack to queue this message and then start a graceful shutdown of the association. All remaining data in queue will be sent after which the association will be shut down.

SCTP_ABORT is used to immediately terminate an association. An abort is sent to the peer and the local TCB is destroyed.

SCTP_UNORDERED is used to specify that the message being sent has no specific order and should be delivered to the peer application as soon as possible. When this flag is absent messages are delivered in order within the stream they are sent, but without respect to order to peer streams.

The flag SCTP_ADDR_OVER is used to specify that an specific address should be used. Normally SCTP will use only one of a multi-homed peers addresses as the primary address to send to. By default, no matter what the to argument is, this primary address is used to send data. By specifying this flag, the user is asking the stack to ignore the primary address and instead use the specified address not only as a lookup mechanism to find the association but also as the actual address to send to.

For a one-to-many type (SOCK_SEQPACKET) socket the flag SCTP_SENDALL can be used as a convenient way to make one send call and have all associations that are under the socket get a copy of the message. Note that this mechanism is quite efficient and makes only one actual copy of the data which is shared by all the associations for sending.

The remaining flags are used for the partial reliability extension (RFC3758) and will only be effective if the peer endpoint supports this extension. This option specifies what local policy the local endpoint should use in skipping data. If none of these options are set, then data is never skipped over.

SCTP_PR_SCTP_TTL is used to indicate that a time based lifetime is being applied to the data. The timetolive argument is then a number of milliseconds for which the data is attempted to be transmitted. If that many milliseconds elapse and the peer has not acknowledged the data, the data will be skipped and no longer transmitted. Note that this policy does not even assure that the data will ever be sent. In times of a congestion with large amounts of data being queued, the timetolive may expire before the first transmission is ever made.

The SCTP_PR_SCTP_BUF based policy transforms the timetolive field into a total number of bytes allowed on the outbound send queue. If that number or more bytes are in queue, then other buffer based sends are looked to be removed and skipped. Note that this policy may also result in the data never being sent if no buffer based sends are in queue and the maximum specified by timetolive bytes is in queue.

The SCTP_PR_SCTP_RTX policy transforms the timetolive into a number of retransmissions to allow. This policy always assures that at a minimum one send attempt is made of the data. After which no more than timetolive retransmissions will be made before the data is skipped.

stream_no is the SCTP stream that you wish to send the message on. Streams in SCTP are reliable (or partially reliable) flows of ordered messages. The context field is used only in the event the message cannot be sent. This is an opaque value that the stack retains and will give to the user when a failed send is given if that notification is enabled (see sctp(4)). Normally a user process can use this value to index some application specific data structure when a send cannot be fulfilled. sctp_sendmsgx() is identical to sctp_sendmsg() with the exception that it takes an array of sockaddr structures in the argument to and adds the additional argument addrcnt which specifies how many addresses are in the array. This allows a caller to implicitly set up an association passing multiple addresses as if sctp_connectx() had been called to set up the association.