gjournal(8) manual page

The gjournal utility is used for journal configuration on the given GEOM provider. The Journal and data may be stored on the same provider or on two separate providers. This is block level journaling, not file system level journaling, which means everything gets logged, e.g.amp; for file systems, it journals both data and metadata. The gjournal GEOM class can talk to file systems, which allows the use of gjournal for file system journaling and to keep file systems in a consistent state. At this time, only UFS file system is supported.

To configure journaling on the UFS file system using gjournal, one should first create a gjournal provider using the gjournal utility, then run newfs(8) or tunefs(8) on it with the -J flag which instructs UFS to cooperate with the gjournal provider below. There are important differences in how journaled UFS works. The most important one is that sync(2) and fsync(2) system calls do not work as expected anymore. To ensure that data is stored on the data provider, the Cm command should be used after calling sync(2). For the best performance possible, soft-updates should be disabled when gjournal is used. It is also safe and recommended to use the async mount(8) option.

When gjournal is configured on top of gmirror(8) or graid3(8) providers, it also keeps them in a consistent state, thus automatic synchronization on power failure or system crash may be disabled on those providers.

The gjournal utility uses on-disk metadata, stored in the provider's last sector, to store all needed information. This could be a problem when an existing file system is converted to use gjournal.

The first argument to gjournal indicates an action to be performed:

label Configures gjournal on the given provider(s). If only one provider is given, both data and journal are stored on the same provider. If two providers are given, the first one will be used as data provider and the second will be used as the journal provider.
Additional options include:

-c Checksum journal records.

-f May be used to convert an existing file system to use gjournal, but only if the journal will be configured on a separate provider and if the last sector in the data provider is not used by the existing file system. If gjournal detects that the last sector is used, it will refuse to overwrite it and return an error. This behavior may be forced by using the -f flag, which will force gjournal to overwrite the last sector.

-h Hardcode provider names in metadata.

-s jsize

Specifies size of the journal if only one provider is used for both data and journal. The default is one gigabyte. Size should be chosen based on provider's load, and not on its size; recommended minimum is twice the size of the physical memory installed. It is not recommended to use gjournal for small file systems (e.g.: only few gigabytes big).

clear Clear metadata on the given providers.

stop Stop the given provider.
Additional options include:

-f

Stop the given provider even if it is opened.

sync Trigger journal switch and enforce sending data to the data provider.

dump Dump metadata stored on the given providers.

list See geom(8).

status

See geom(8).

load See geom(8).

unload

See geom(8).

Additional options include:

-v

Be more verbose.

sysctl name Ta Type	Changeable
debug Ta integer	yes
switch_time Ta integer	yes
force_switch Ta integer	yes
parallel_flushes Ta integer	yes
accept_immediately Ta integer	yes
parallel_copies Ta integer	yes
record_entries Ta integer	yes
optimize Ta integer	yes

`debug`	Setting a non-zero value enables debugging at various levels. Debug level 1 will record actions at a journal level, relating to journal switches, metadata updates, etc. Debug level 2 will record actions at a higher level, relating to the numbers of entries in journals, access requests, etc. Debug level 3 will record verbose detail, including insertion of I/Os to the journal.
`switch_time`
	The maximum number of seconds a journal is allowed to remain open before switching to a new journal.
`force_switch`
	Force a journal switch when the journal uses more than N% of the free journal space.
`parallel_flushes`
	The number of flush I/O requests to be sent in parallel when flushing the journal to the data provider.
`accept_immediately`
	The maximum number of I/O requests accepted at the same time.
`parallel_copies`
	The number of copy I/O requests to send in parallel.
`record_entries`
	The maximum number of record entries to allow in a single journal.
`optimize`
	Controls whether entries in a journal will be optimized by combining overlapping I/Os into a single I/O and reordering the entries in a journal. This can be disabled by setting the sysctl to 0.

sysctl name Ta Type	Changeable
used Ta integer	no
limit Ta integer	yes
divisor Ta integer	no
switch Ta integer	yes
misses Ta integer	yes
alloc_failures Ta integer	yes

`used`	The number of bytes currently allocated to the cache.
`limit`	The maximum number of bytes to be allocated to the cache.
`divisor`
	Sets the cache size to be used as a proportion of kmem_size. A value of 2 (the default) will cause the cache size to be set to 1/2 of the kmem_size.
`switch`	Force a journal switch when this percentage of cache has been used.
`misses`	The number of cache misses, when data has been read, but was not found in the cache.
`alloc_failures`
	The number of times memory failed to be allocated to the cache because the cache limit was hit.

sysctl name Ta Type	Changeable
skipped_bytes Ta integer	yes
combined_ios Ta integer	yes
switches Ta integer	yes
wait_for_copy Ta integer	yes
journal_full Ta integer	yes
low_mem Ta integer	yes

Manual Pages — GJOURNAL

NAME

CONTENTS

SYNOPSIS

DESCRIPTION

EXIT STATUS

EXAMPLES

SYSCTLS

cache

stats

SEE ALSO

HISTORY

AUTHORS

-c	Checksum journal records.
-f	May be used to convert an existing file system to use gjournal, but only if the journal will be configured on a separate provider and if the last sector in the data provider is not used by the existing file system. If gjournal detects that the last sector is used, it will refuse to overwrite it and return an error. This behavior may be forced by using the -f flag, which will force gjournal to overwrite the last sector.
-h	Hardcode provider names in metadata.
-s jsize
	Specifies size of the journal if only one provider is used for both data and journal. The default is one gigabyte. Size should be chosen based on provider's load, and not on its size; recommended minimum is twice the size of the physical memory installed. It is not recommended to use gjournal for small file systems (e.g.: only few gigabytes big).

clear	Clear metadata on the given providers.
stop	Stop the given provider. Additional options include:

sync	Trigger journal switch and enforce sending data to the data provider.
dump	Dump metadata stored on the given providers.
list	See geom(8).
status
	See geom(8).
load	See geom(8).
unload
	See geom(8).

`skipped_bytes`
	The number of bytes skipped.
`combined_ios`
	The number of I/Os which were combined by journal optimization.
`switches`
	The number of journal switches.
`wait_for_copy`
	The number of times the journal switch process had to wait for the previous journal copy to complete.
`journal_full`
	The number of times the journal was almost full, forcing a journal switch.
`low_mem`
	The number of times the low_mem hook was called.