tail head cat sleep
QR code linking to this page

Manual Pages  — RUM

NAME

rum – Ralink Technology USB IEEE 802.11a/b/g wireless network device

CONTENTS

SYNOPSIS

To compile this driver into the kernel, place the following lines in your kernel configuration file: device ehci device uhci device ohci device usb device rum device wlan device wlan_amrr

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

if_rum_load="YES"

DESCRIPTION

The rum driver supports USB 2.0 and PCI Express Mini Card wireless adapters based on the Ralink RT2501USB and RT2601USB chipsets.

Ralink PCI Express Mini Card adapters show up as normal USB 2.0 devices and are thus handled by the rum driver.

The RT2501USB chipset is the second generation of 802.11a/b/g adapters from Ralink. It consists of two integrated chips, an RT2571W MAC/BBP and an RT2528 or RT5226 radio transceiver.

The RT2601USB chipset consists of two integrated chips, an RT2671 MAC/BBP and an RT2527 or RT5225 radio transceiver. This chipset uses the MIMO (multiple-input multiple-output) technology with multiple antennas to extend the operating range of the adapter and to achieve higher throughput.

All chips have hardware support for WEP, AES-CCM, TKIP, and Michael cryptographic operations.

rum supports station, adhoc, adhoc-demo, hostap, and monitor mode operation. Only one virtual interface may be configured at any time. For more information on configuring this device, see ifconfig(8).

HARDWARE

The rum driver supports USB 2.0 wireless adapters based on the Ralink RT2501USB and RT2601USB chipsets, including:

Card Bus

3Com Aolynk WUB320g
USB

Abocom WUG2700 Ta
USB

Airlink101 AWLL5025
USB

ASUS WL-167g ver 2
USB

Belkin F5D7050 ver 3
USB

Belkin F5D9050 ver 3
USB

Buffalo WLI-U2-SG54HP
USB

Buffalo WLI-U2-SG54HG
USB

Buffalo WLI-U2-G54HP
USB

Buffalo WLI-UC-G
USB

CNet CWD-854 ver F
USB

Conceptronic C54RU ver 2
USB

Corega CG-WLUSB2GO
USB

D-Link DWA-110
USB

D-Link DWA-111
USB

D-Link DWL-G122 rev C1
USB

D-Link WUA-1340
USB

Digitus DN-7003GR
USB

Edimax EW-7318USG
USB

Gigabyte GN-WB01GS
USB

Gigabyte GN-WI05GS
USB

Hawking HWUG1
USB

Hawking HWU54DM
USB

Hercules HWGUSB2-54-LB
USB

Hercules HWGUSB2-54V2-AP
USB

LevelOne WNC-0301USB v3
USB

Linksys WUSB54G rev C
USB

Linksys WUSB54GR
USB

Planex GW-US54HP
USB

Planex GW-US54Mini2
USB

Planex GW-USMM
USB

Senao NUB-3701
USB

Sitecom WL-113 ver 2
USB

Sitecom WL-172
USB

Sweex LW053
USB

TP-LINK TL-WN321G v1/v2/v3
USB

EXAMPLES

Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev rum0 inet 192.168.0.20 \
    netmask 0xffffff00

Join a specific BSS network with network name "my_net":

    ifconfig wlan create wlandev rum0 ssid my_net up

Join a specific BSS network with 64-bit WEP encryption:

ifconfig wlan create wlandev rum0 ssid my_net \
        wepmode on wepkey 0x1234567890 weptxkey 1 up

Join a specific BSS network with 128-bit WEP encryption:

ifconfig wlan create wlandev rum0 wlanmode adhoc ssid my_net \
    wepmode on wepkey 0x01020304050607080910111213 weptxkey 1

DIAGNOSTICS

rum%d: could not load 8051 microcode An error occurred while attempting to upload the microcode to the onboard 8051 microcontroller unit. The driver will reset the hardware. This should not happen.

SEE ALSO

intro(4), netintro(4), usb(4), wlan(4), wlan_amrr(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), wlan_xauth(4), hostapd(8), ifconfig(8), wpa_supplicant(8). http://www.ralinktech.com/

Ralink Technology,

HISTORY

The rum driver first appeared in OpenBSD 4.0 .

AUTHORS

The original rum driver was written by Niall O'Higgins <Mt niallo@openbsd.org> and Damien Bergamini <Mt damien@openbsd.org>.

RUM (4) November 8, 2018

tail head cat sleep
QR code linking to this page


Please direct any comments about this manual page service to Ben Bullock. Privacy policy.