tail head cat sleep
QR code linking to this page
Main index Section 4
Go to:
Options

Manual Pages  — IX

NAME

ix – Intel 10Gb Ethernet driver

CONTENTS

SYNOPSIS

To compile this driver into the kernel, place the following lines in your kernel configuration file: device iflib device ix

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): 

if_ix_load="YES"

DESCRIPTION

The ix driver provides support for Intel(R) 10Gb Ethernet PCIe adapters. The driver supports Jumbo Frames, MSIX, TSO, and RSS.

For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements listed apply to use with FreeBSD .

Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 9710.

This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).

HARDWARE

The ix driver supports Intel 10Gb Ethernet PCIe adapters, including:

LOADER TUNABLES

The ix driver supports the following loader tunables:
hw.ix.max_interrupt_rate
  Maximum interrupts per second.
hw.ix.flow_control
  Default flow control used for all adapters.
hw.ix.advertise_speed
  Default advertised speed for all adapters.
hw.ix.enable_msix
  Enable Message Signalled Interrupts (MSI-X).
hw.ix.allow_unsupported_sfp
  Allow unsupported small form-factor pluggable (SFP) modules. Use at your own risk.
hw.ix.enable_fdir
  Enable Flow Director. Flow Director directs Ethernet packets to the core where the packet consuming process, application, container, or microservice is running.
hw.ix.enable_rss
  Enable Receive-Side Scaling (RSS). When RSS is enabled, all of the receive data processing for a particular TCP connection is shared across multiple processors or processor cores. Without RSS, all of the processing is performed by a single processor, resulting in inefficient system cache utilization. This has no effect if your system has only one processing unit.
hw.ix.enable_aim
  Enable Adaptive Interrupt Moderation (AIM). Vary the interrupt rate over time based on the traffic for that interrupt vector.

DIAGNOSTICS

ix%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ix%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ix%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection (cable).

SUPPORT

For general information and support, go to the Intel support website at: http://support.intel.com.

If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to <Mt freebsd@intel.com>.

SEE ALSO

altq(4), arp(4), iflib(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8), sysctl(8)

HISTORY

The ix device driver first appeared in FreeBSD 7.0 .

AUTHORS

The ix driver was written by Intel Corporation <Mt freebsd@intel.com>.

CAVEATS

Intel (R) Flow director support is not fully implemented in FreeBSD at this time and additional work is required before those features can be supported.

Enabling flow director may route traffic to the wrong RX queue of the NIC, resulting in sub-optimal performance on the receive side.

IX (4) October 26, 2024
tail head cat sleep
QR code linking to this page
Main index Section 4
Go to:
Options

Please direct any comments about this manual page service to Ben Bullock. Privacy policy.

“ The most horrifying thing about Unix is that, no matter how many times you hit yourself over the head with it, you never quite manage to lose consciousness. It just goes on and on. ”
— Patrick Sobalvarro