| Main index | Section 4 | Options |
Or, to load the driver as a module at boot, place the following line in loader.conf(5):
nvme_load="YES"
Most users will also want to enable nvd(4) or nda(4) to expose NVM Express namespaces as disk devices which can be partitioned. Note that in NVM Express terms, a namespace is roughly equivalent to a SCSI LUN.
The nvme driver creates controller device nodes in the format /dev/nvmeX and namespace device nodes in the format /dev/nvmeXnsY. Note that the NVM Express specification starts numbering namespaces at 1, not 0, and this driver follows that convention.
To force a single I/O queue pair shared by all CPUs, set the following tunable value in loader.conf(5):
hw.nvme.per_cpu_io_queues=0
To assign more than one CPU per I/O queue pair, thereby reducing the number of MSI-X vectors consumed by the device, set the following tunable value in loader.conf(5):
hw.nvme.min_cpus_per_ioq=X
To force legacy interrupts for all nvme driver instances, set the following tunable value in loader.conf(5):
hw.nvme.force_intx=1
Note that use of INTx implies disabling of per-CPU I/O queue pairs.
To control maximum amount of system RAM in bytes to use as Host Memory Buffer for capable devices, set the following tunable:
hw.nvme.hmb_max
The default value is 5% of physical memory size per device.
The nvd(4) driver is used to provide a disk driver to the system by default. The nda(4) driver can also be used instead. The nvd(4) driver performs better with smaller transactions and few TRIM commands. It sends all commands directly to the drive immediately. The nda(4) driver performs better with larger transactions and also collapses TRIM commands giving better performance. It can queue commands to the drive; combine BIO_DELETE commands into a single trip; and use the CAM I/O scheduler to bias one type of operation over another. To select the nda(4) driver, set the following tunable value in loader.conf(5):
hw.nvme.verbose_cmd_dump=1
| dev.nvme.0.num_cpus_per_ioq | |
| (R) Number of CPUs associated with each I/O queue pair. | |
| dev.nvme.0.int_coal_time | |
| (R/W) Interrupt coalescing timer period in microseconds. Set to 0 to disable. | |
| dev.nvme.0.int_coal_threshold | |
| (R/W) Interrupt coalescing threshold in number of command completions. Set to 0 to disable. | |
The following queue pair-level sysctls are currently implemented. Admin queue sysctls take the format of dev.nvme.0.adminq and I/O queue sysctls take the format of dev.nvme.0.ioq0.
| dev.nvme.0.ioq0.num_entries | |
| (R) Number of entries in this queue pair's command and completion queue. | |
| dev.nvme.0.ioq0.num_tr | |
| (R) Number of nvme_tracker structures currently allocated for this queue pair. | |
| dev.nvme.0.ioq0.num_prp_list | |
| (R) Number of nvme_prp_list structures currently allocated for this queue pair. | |
| dev.nvme.0.ioq0.sq_head | |
| (R) Current location of the submission queue head pointer as observed by the driver. The head pointer is incremented by the controller as it takes commands off of the submission queue. | |
| dev.nvme.0.ioq0.sq_tail | |
| (R) Current location of the submission queue tail pointer as observed by the driver. The driver increments the tail pointer after writing a command into the submission queue to signal that a new command is ready to be processed. | |
| dev.nvme.0.ioq0.cq_head | |
| (R) Current location of the completion queue head pointer as observed by the driver. The driver increments the head pointer after finishing with a completion entry that was posted by the controller. | |
| dev.nvme.0.ioq0.num_cmds | |
| (R) Number of commands that have been submitted on this queue pair. | |
| dev.nvme.0.ioq0.dump_debug | |
| (W) Writing 1 to this sysctl will dump the full contents of the submission and completion queues to the console. | |
In addition to the typical pci attachment, the nvme driver supports attaching to a ahci(4) device. Intel's Rapid Storage Technology (RST) hides the nvme device behind the AHCI device due to limitations in Windows. However, this effectively hides it from the FreeBSD kernel. To work around this limitation, FreeBSD detects that the AHCI device supports RST and when it is enabled. See ahci(4) for more details.
This man page was written by Jim Harris <Mt jimharris@FreeBSD.org>.
| NVME (4) | June 6, 2020 |
| Main index | Section 4 | Options |
Please direct any comments about this manual page service to Ben Bullock. Privacy policy.
| “ | Using Unix is the computing equivalent of listening only to music by David Cassidy | ” |
| — Rob Pike | ||