| Main index | Section 4 | Options |
Firmware is also needed, and provided by: device runfw
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
if_run_load="YES" runfw_load="YES"
The RT2700U chipset consists of two integrated chips, an RT2770 MAC/BBP and an RT2720 (1T2R) or RT2750 (dual-band 1T2R) radio transceiver.
The RT2800U chipset consists of two integrated chips, an RT2870 MAC/BBP and an RT2820 (2T3R) or RT2850 (dual-band 2T3R) radio transceiver.
The RT3000U is a single-chip solution based on an RT3070 MAC/BBP and an RT3020 (1T1R), RT3021 (1T2R) or RT3022 (2T2R) single-band radio transceiver.
The RT3900E is a single-chip USB 2.0 802.11n solution. The MAC/Baseband Processor can be an RT3593, RT5390, RT5392 or an RT5592. The radio can be an RT3053, RT5370, RT5372 or an RT5572. The RT3053 chip operates in the 2GHz and 5GHz spectra and supports up to 3 transmit paths and 3 receiver paths (3T3R). The RT5370 chip operates in the 2GHz spectrum and supports 1 transmit path and 1 receiver path (1T1R). The RT5372 chip operates in the 2GHz spectrum and supports up to 2 transmit paths and 2 receiver paths (2T2R). The RT5572 chip operates in the 2GHz and 5GHz spectra and supports up to 2 transmit paths and 2 receiver paths (2T2R).
These are the modes the run driver can operate in:
| BSS mode | Also known as infrastructure mode, this is used when associating with an access point, through which all traffic passes. This mode is the default. |
| Host AP mode | In this mode the driver acts as an access point (base station) for other cards. |
| monitor mode | In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points. |
The run driver can be configured to use Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA-PSK and WPA2-PSK). WPA is the de facto encryption standard for wireless networks. It is strongly recommended that WEP not be used as the sole mechanism to secure wireless communication, due to serious weaknesses in it. The run driver offloads both encryption and decryption of data frames to the hardware for the WEP40, WEP104, TKIP(+MIC) and CCMP ciphers.
The run driver can be configured at runtime with ifconfig(8).
ifconfig wlan create wlandev run0 inet 192.0.2.20/24
Join a specific BSS network with network name my_net:
ifconfig wlan create wlandev run0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev run0 ssid my_net \
wepmode on wepkey 0x1234567890 weptxkey 1 up
Join a specific BSS network with 128-bit WEP encryption:
ifconfig wlan create wlandev run0 wlanmode adhoc ssid my_net \
wepmode on wepkey 0x01020304050607080910111213 weptxkey 1
| run%d: failed load firmware of file runfw | For some reason, the driver was unable to read the microcode file from the filesystem. The file might be missing or corrupted. |
| run%d: could not load 8051 microcode | An error occurred while attempting to upload the microcode to the onboard 8051 microcontroller unit. |
| run%d: device timeout | A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware. This should not happen. |
| RUN (4) | November 10, 2024 |
| Main index | Section 4 | Options |
Please direct any comments about this manual page service to Ben Bullock. Privacy policy.
| “ | There are 10 types of people in the world: those who understand binary, and those who don't. | ” |