tail head cat sleep
QR code linking to this page

Manual Pages  — SPPPCONTROL

NAME

spppcontrol – display or set parameters for an sppp interface

CONTENTS

SYNOPSIS


spppcontrol [-v] ifname [parameter[=value]] [...]

DESCRIPTION

The sppp(4) driver might require a number of additional arguments or optional parameters besides the settings that can be adjusted with ifconfig(8). These are things like authentication protocol parameters, but also other tunable configuration variables. The spppcontrol utility can be used to display the current settings, or adjust these parameters as required.

For whatever intent spppcontrol is being called, at least the parameter ifname needs to be specified, naming the interface for which the settings are to be performed or displayed. Use ifconfig(8), or netstat(1) to see which interfaces are available.

If no other parameter is given, spppcontrol will just list the current settings for ifname and exit. The reported settings include the current PPP phase the interface is in, which can be one of the names dead, establish, authenticate, network, or terminate. If an authentication protocol is configured for the interface, the name of the protocol to be used, as well as the system name to be used or expected will be displayed, plus any possible options to the authentication protocol if applicable. Note that the authentication secrets (sometimes also called keys) are not being returned by the underlying system call, and are thus not displayed.

If any additional parameter is supplied, superuser privileges are required, and the command works in the "set" mode. This is normally done quietly, unless the option -v is also enabled, which will cause a final printout of the settings as described above once all other actions have been taken. Use of this mode will be rejected if the interface is currently in any other phase than dead. Note that you can force an interface into dead phase by calling ifconfig(8) with the parameter down.

The currently supported parameters include:
authproto=protoname Set both, his and my authentication protocol to protoname. The protocol name can be one of "chap", "pap", or "none". In the latter case, the use of an authentication protocol will be turned off for the named interface. This has the side-effect of clearing the other authentication-related parameters for this interface as well (i.e., system name and authentication secret will be forgotten).
myauthproto=protoname Same as above, but only for my end of the link. I.e., this is the protocol when remote is authenticator, and I am the peer required to authenticate.
hisauthproto=protoname Same as above, but only for his end of the link.
myauthname=name Set my system name for the authentication protocol.
hisauthname=name Set his system name for the authentication protocol. For CHAP, this will only be used as a hint, causing a warning message if remote did supply a different name. For PAP, it is the name remote must use to authenticate himself (in connection with his secret).
myauthsecret=secret Set my secret (key, password) for use in the authentication phase. For CHAP, this will be used to compute the response hash value, based on remote's challenge. For PAP, it will be transmitted as plain text together with the system name. Do not forget to quote the secrets from the shell if they contain shell metacharacters (or white space).
myauthkey=secret Same as above.
hisauthsecret=secret Same as above, to be used if we are an authenticator and the remote peer needs to authenticate.
hisauthkey= secret Same as above.
callin Require remote to authenticate himself only when he is calling in, but not when we are caller. This is required for some peers that do not implement the authentication protocols symmetrically (like Ascend routers, for example).
always The opposite of callin. Require remote to always authenticate, regardless of which side is placing the call. This is the default, and will not be explicitly displayed in the "list" mode.
norechallenge Only meaningful with CHAP. Do not re-challenge peer once the initial CHAP handshake was successful. Used to work around broken peer implementations that cannot grok being re-challenged once the connection is up.
rechallenge With CHAP, send re-challenges at random intervals while the connection is in network phase. (The intervals are currently in the range of 300 through approximately 800 seconds.) This is the default, and will not be explicitly displayed in the "list" mode.
lcp-timeout=timeout-value Allows to change the value of the LCP restart timer. Values are specified in milliseconds. The value must be between 10 and 20000 ms, defaulting to 3000 ms.
enable-vj Enable negotiation of Van Jacobsen header compression. (Enabled by default.)
disable-vj Disable negotiation of Van Jacobsen header compression.
enable-ipv6 Enable negotiation of the IPv6 network control protocol. (Enabled by default if the kernel has IPv6 enabled.)
disable-ipv6 Disable negotiation of the IPv6 network control protocol. Since every IPv4 interface in an IPv6-enabled kernel automatically gets an IPv6 address assigned, this option provides for a way to administratively prevent the link from attempting to negotiate IPv6. Note that initialization of an IPv6 interface causes a multicast packet to be sent, which can cause unwanted traffic costs (for dial-on-demand interfaces).

EXAMPLES

# spppcontrol bppp0
bppp0:  phase=dead
        myauthproto=chap myauthname="uriah"
        hisauthproto=chap hisauthname="ifb-gw" norechallenge
        lcp-timeout=3000
        enable-vj
        enable-ipv6

Display the settings for bppp0. The interface is currently in dead phase, i.e., the LCP layer is down, and no traffic is possible. Both ends of the connection use the CHAP protocol, my end tells remote the system name "uriah", and remote is expected to authenticate by the name "ifb-gw". Once the initial CHAP handshake was successful, no further CHAP challenges will be transmitted. There are supposedly some known CHAP secrets for both ends of the link which are not being shown.

# spppcontrol bppp0 \
        authproto=chap \
        myauthname=uriah myauthsecret='some secret' \
        hisauthname=ifb-gw hisauthsecret='another' \
        norechallenge

A possible call to spppcontrol that could have been used to bring the interface into the state shown by the previous example.

SEE ALSO

netstat(1), sppp(4), ifconfig(8)

B. Lloyd, W. Simpson, RFC 1334, PPP Authentication Protocols,

W. Simpson, Editor, RFC 1661, The Point-to-Point Protocol (PPP),

W. Simpson, RFC 1994, PPP Challenge Handshake Authentication Protocol (CHAP),

HISTORY

The spppcontrol utility appeared in FreeBSD 3.0 .

AUTHORS

The program was written by Jörg Wunsch, Dresden.

SPPPCONTROL (8) December 30, 2001

tail head cat sleep
QR code linking to this page


Please direct any comments about this manual page service to Ben Bullock. Privacy policy.

It's a UNIX system, I know this!
— Lex Murphy, Jurassic Park