|Main index||Section 4||Options|
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
All of these NICs are capable of 10, 100 and 1000Mbps speeds over CAT5 copper cable, except for the SysKonnect SK-9D41 which supports only 1000Mbps over multimode fiber. The BCM570x builds upon the technology of the Alteon Tigon II. It has two R4000 CPU cores and is PCI v2.2 and PCI-X v1.0 compliant. It supports IP, TCP and UDP checksum offload for both receive and transmit, multiple RX and TX DMA rings for QoS applications, rules-based receive filtering, and VLAN tag stripping/insertion as well as a 256-bit multicast hash filter. Additional features may be provided via value-add firmware updates. The BCM570x supports TBI (ten bit interface) and GMII transceivers, which means it can be used with either copper or 1000baseX fiber applications. Note however the device only supports a single speed in TBI mode.
Most BCM5700-based cards also use the Broadcom BCM5401 or BCM5411 10/100/1000 copper gigabit transceivers, which support autonegotiation of 10, 100 and 1000Mbps modes in full or half duplex.
The BCM5700, BCM5701, BCM5702, BCM5703, BCM5704, BCM5714, BCM5717, BCM5719, BCM5720, BCM5780 and BCM57765 also support jumbo frames, which can be configured via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit jumbo frames. Using jumbo frames can greatly improve performance for certain tasks, such as file transfers and data streaming.
The bge driver supports the following media types:
|autoselect||Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf(5).|
|Set 10Mbps operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.|
|100baseTX||Set 100Mbps (Fast Ethernet) operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.|
|1000baseTX||Set 1000baseTX operation over twisted pair. Only full-duplex mode is supported.|
|1000baseSX||Set 1000Mbps (Gigabit Ethernet) operation. Both full-duplex and half-duplex modes are supported.|
The bge driver supports the following media options:
|Force full duplex operation.|
|Force half duplex operation.|
For more information on configuring this device, see ifconfig(8).
|Allow the ASF feature for cooperating with IPMI. Can cause system lockup problems on a small number of systems. Enabled by default.|
|Non-zero value enables MSI support on the Ethernet hardware. The default value is 1.|
|Allow collapsing multiple transmit buffers into a single buffer to increase transmit performance with the cost of CPU cycles. The default value is 0 to disable transmit buffer collapsing.|
|Enable UDP transmit checksum offloading even if controller can generate UDP datagrams with checksum value 0. UDP datagrams with checksum value 0 can confuse receiver host as it means sender did not compute UDP checksum. The default value is 0 which disables UDP transmit checksum offloading. The interface need to be brought down and up again before a change takes effect.|
|bge%d: couldn't map memory||A fatal initialization error has occurred.|
|bge%d: couldn't map ports||A fatal initialization error has occurred.|
|bge%d: couldn't map interrupt||A fatal initialization error has occurred.|
|bge%d: no memory for softc struct!||The driver failed to allocate memory for per-device instance information during initialization.|
|bge%d: failed to enable memory mapping!||The driver failed to initialize PCI shared memory mapping. This might happen if the card is not in a bus-master slot.|
|bge%d: firmware handshake timed out, found 0xffffffff||The device was physically disconnected from the system, or there is a problem with the device causing it to stop responding to the host it is attached to.|
|bge%d: no memory for jumbo buffers!||The driver failed to allocate memory for jumbo frames during initialization.|
|bge%d: watchdog timeout||The device has stopped responding to the network, or there is a problem with the network connection (cable).|
|BGE (4)||August 18, 2017|
|Main index||Section 4||Options|
Please direct any comments about this manual page service to Ben Bullock.
|“||Our grievance is not just against Unix itself, but against the cult of Unix zealots who defend and nurture it. They take the heat, disease, and pestilence as givens, and, as ancient shamans did, display their wounds, some self-inflicted, as proof of their power and wizardry. We aim, through bluntness and humor, to show them that they pray to a tin god, and that science, not religion, is the path to useful and friendly technology.||”|
|— The Unix Haters' handbook|