tail head cat sleep
QR code linking to this page

Manual Pages  — NTP_KEYS

NAME

ntp.keys – NTP symmetric key file format

CONTENTS

NAME

ntp.keys – NTP symmetric key file format

SYNOPSIS


ntp.keys [--option-name] [--option-name value]

All arguments must be options.

DESCRIPTION

This document describes the format of an NTP symmetric key file. For a description of the use of this type of file, see the "Authentication Support" section of the ntp.conf(5) page.

ntpd(8) reads its keys from a file specified using the -k command line option or the keys statement in the configuration file. While key number 0 is fixed by the NTP standard (as 56 zero bits) and may not be changed, one or more keys numbered between 1 and 65535 may be arbitrarily set in the keys file.

The key file uses the same comment conventions as the configuration file. Key entries use a fixed format of the form

where keyno is a positive integer (between 1 and 65535), type is the message digest algorithm, key is the key itself, and opt_IP_list is an optional comma-separated list of IPs where the keyno should be trusted. that are allowed to serve time. Each IP in opt_IP_list may contain an optional /subnetbits specification which identifies the number of bits for the desired subnet of trust. If opt_IP_list is empty, any properly-authenticated message will be accepted.

The key may be given in a format controlled by the type field. The type MD5 is always supported. If ntpd was built with the OpenSSL library then any digest library supported by that library may be specified. However, if compliance with FIPS 140-2 is required the type must be either SHA or SHA1.

What follows are some key types, and corresponding formats:

MD5 The key is 1 to 16 printable characters terminated by an EOL, whitespace, or a # (which is the "start of comment" character).

SHA
SHA1
RMD160
  The key is a hex-encoded ASCII string of 40 characters, which is truncated as necessary.

Note that the keys used by the ntpq(8) and ntpdc(8) programs are checked against passwords requested by the programs and entered by hand, so it is generally appropriate to specify these keys in ASCII format.

OPTIONS

--help Display usage information and exit.
--more-help Pass the extended usage information through a pager.
--version [{v|c|n}] Output version of program and exit. The default mode is `v', a simple version. The `c' mode will print copyright information and `n' will print the full copyright notice.

OPTION PRESETS

Any option that is not marked as not presettable may be preset by loading values from environment variables named:
  NTP_KEYS_<option-name> or NTP_KEYS

ENVIRONMENT

See OPTION PRESETS for configuration environment variables.

FILES

/etc/ntp.keys
  the default name of the configuration file

EXIT STATUS

One of the following exit values will be returned:
0 (EXIT_SUCCESS) Successful program execution.
1 (EXIT_FAILURE) The operation failed or the command syntax was not valid.
70 (EX_SOFTWARE) libopts had an internal operational error. Please report it to autogen-users@lists.sourceforge.net. Thank you.

SEE ALSO

ntp.conf(5), ntpd(8), ntpdate(8), ntpdc(8), sntp(8)

AUTHORS

The University of Delaware and Network Time Foundation

COPYRIGHT

Copyright (C) 1992-2017 The University of Delaware and Network Time Foundation all rights reserved. This program is released under the terms of the NTP license, <http://ntp.org/license>.

BUGS

Please send bug reports to: http://bugs.ntp.org, bugs@ntp.org

NOTES

This document was derived from FreeBSD.

This manual page was AutoGen-erated from the ntp.keys option definitions.


SunOS 5.10 NTP_KEYS (5) August 14 2018

tail head cat sleep
QR code linking to this page


Please direct any comments about this manual page service to Ben Bullock. Privacy policy.