dhclient(8) manual page

The dhclient utility provides a means for configuring network interfaces using DHCP, BOOTP, or if these protocols fail, by statically assigning an address.

The name of the network interface that dhclient should attempt to configure must be specified on the command line.

The options are as follows:

-b

Forces dhclient to immediately move to the background.

-c file

Specify an alternate location, file, for the configuration file.

-d

Forces dhclient to always run as a foreground process. By default, dhclient runs in the foreground until it has configured the interface, and then will revert to running in the background.

-l file

Specify an alternate location, file, for the leases file.

-p file

Specify an alternate location for the PID file. The default is /var/run/dhclient/dhclient.interface .pid.

-q

Forces dhclient to be less verbose on startup.

-u

Forces dhclient to reject leases with unknown options in them. The default behaviour is to accept such lease offers.

The DHCP protocol allows a host to contact a central server which maintains a list of IP addresses which may be assigned on one or more subnets. A DHCP client may request an address from this pool, and then use it on a temporary basis for communication on the network. The DHCP protocol also provides a mechanism whereby a client can learn important details about the network to which it is attached, such as the location of a default router, the location of a name server, and so on.

On startup, dhclient reads /etc/dhclient.conf for configuration instructions. It then gets a list of all the network interfaces that are configured in the current system. It then attempts to configure each interface with DHCP.

In order to keep track of leases across system reboots and server restarts, dhclient keeps a list of leases it has been assigned in the /var/db/dhclient.leases.IFNAME file. IFNAME represents the network interface of the DHCP client (e.g., em0), one for each interface. On startup, after reading the dhclient.conf(5) file, dhclient reads the leases file to refresh its memory about what leases it has been assigned.

Old leases are kept around in case the DHCP server is unavailable when dhclient is first invoked (generally during the initial system boot process). In that event, old leases from the dhclient.leases.IFNAME file which have not yet expired are tested, and if they are determined to be valid, they are used until either they expire or the DHCP server becomes available.

A mobile host which may sometimes need to access a network on which no DHCP server exists may be preloaded with a lease for a fixed address on that network. When all attempts to contact a DHCP server have failed, dhclient will try to validate the static lease, and if it succeeds, it will use that lease until it is restarted.

A mobile host may also travel to some networks on which DHCP is not available but BOOTP is. In that case, it may be advantageous to arrange with the network administrator for an entry on the BOOTP database, so that the host can boot quickly on that network rather than cycling through the list of old leases.

You must have the Berkeley Packet Filter (BPF) configured in your kernel. The dhclient utility requires at least one /dev/bpf* device for each broadcast network interface that is attached to your system. See bpf(4) for more information.

dhclient.conf(5), dhclient.leases(5), dhclient-script(8)

The dhclient utility uses capsicum(4) to sandbox the main process. If the requisite kernel support is not available, the main process will attempt to run in a chroot(2) sandbox instead. This will fail if the process is jailed or the kern.chroot_allow_open_directories sysctl is set to 0.

“	Never write it in C if you can do it in `awk'; Never do it in `awk' if `sed' can handle it; Never use `sed' when `tr' can do the job; Never invoke `tr' when `cat' is sufficient; Avoid using `cat' whenever possible.	”
— Taylor's Laws of Programming

Manual Pages — DHCLIENT

NAME

CONTENTS

SYNOPSIS

DESCRIPTION

NOTES

FILES

SEE ALSO

AUTHORS

BUGS

-b
	Forces dhclient to immediately move to the background.
-c file
	Specify an alternate location, file, for the configuration file.
-d
	Forces dhclient to always run as a foreground process. By default, dhclient runs in the foreground until it has configured the interface, and then will revert to running in the background.
-l file
	Specify an alternate location, file, for the leases file.
-p file
	Specify an alternate location for the PID file. The default is `/var/run/dhclient/dhclient.`interface `.pid`.
-q
	Forces dhclient to be less verbose on startup.
-u
	Forces dhclient to reject leases with unknown options in them. The default behaviour is to accept such lease offers.

`/etc/dhclient.conf`	DHCP client configuration file
`/var/db/dhclient.leases.`IFNAME	database of acquired leases